Factors Affecting Distillation Column Operation

The performance of a distillation column is determined by many factors, for example:

■p feed conditions

• composition of feed

• trace elements that can severely affect the VLE of liquid mixtures.--"!

'p internal liquid and fluid flow conditions 'p state of trays (packings) weather conditions

Some of these will be discussed below to give an idea of the complexity of the distillation process.

Feed Conditions

The state of the feed mixture and feed composition affects the operating lines and hence the number of stages required for separation. It also affects the location of feed tray. During operation, if the deviations from design specifications are excessive, then the column may no longer be able handle the separation task. To overcome the problems associated with the feed, some column are designed to have multiple feed points when the feed is expected to containing varying amounts of components.

Reflux Conditions

Reflux Conditions

Heat Balance Distallation Columns

As the reflux ratio is increased, the gradient of operating line for the rectification section moves towards a maximum value of 1. Physically, what this means is that more and more liquid that is rich in the more volatile components are being recycled back into the column. Separation then becomes better and thus less trays are needed to achieve the same degree of separation. Minimum trays are required under total


reflux conditions, i.e. there is no withdrawal of distillate.

On the other hand, as reflux is decreased, the operating line for the rectification section moves towards the equilibrium line. The 'pinch' between operating and equilibrium lines becomes more pronounced and more and more trays are required.This is easy to verify using the McCabe-Thiele method.

The limiting condition occurs at minimum reflux ration, when an infinite number of trays will be required to effect separation. Most columns are designed to operate between 1.2 to 1.5 times the minimum reflux ratio because this is approximately the region of minimum operating costs (more reflux means higher reboiler duty).

Vapour Flow Conditions

Adverse vapour flow conditions can cause foaming

• entrainment

• weeping/dumping

flooding Foaming

Foaming refers to the expansion of liquid due to passage of vapour or gas. Although it provides high interfacial liquid-vapour contact, excessive foaming often leads to liquid buildup on trays. In some cases, foaming may be so bad that the foam mixes with liquid on the tray above. Whether foaming will occur depends primarily on physical properties of the liquid mixtures, but is sometimes due to tray designs and condition. Whatever the cause, separation efficiency is always reduced. Entrainment

Entrainment refers to the liquid carried by vapour up to the tray above and is again caused by high vapour flow rates. It is detrimental because tray efficiency is reduced: lower volatile material is carried to a plate holding liquid of higher volatility. It could also contaminate high purity distillate. Excessive entrainment can lead to flooding. Weeping/Dumping

This phenomenon is caused by low vapour flow. The pressure exerted by the vapour is insufficient to hold up the liquid on the tray. Therefore, liquid starts to leak through perforations. Excessive weeping will lead to dumping. That is the liquid on all trays will crash (dump) through to the base of the column (via a domino effect) and the column will have to be re-started. Weeping is indicated by a sharp pressure drop in the column and reduced separation efficiency. Flooding

Flooding is brought about by excessive vapour flow, causing liquid to be entrained in the vapour up the column. The increased pressure from excessive vapour also backs up the liquid in the downcomer, causing an increase in liquid holdup on the plate above. Depending on the degree of flooding, the maximum capacity of the column may be severely reduced. Flooding is detected by sharp increases in column differential pressure and significant decrease in separation efficiency.

Column Diameter

Most of the above factors that affect column operation is due to vapour flow conditions: either excessive or too low. Vapour flow velocity is dependent on column diameter. Weeping determines the minimum vapour flow required while flooding determines the maximum vapour flow V allowed, hence column capacity. Thus, if the column diameter is not sized properly, the column will not perform well. Not only will operational problems occur, the desired separation duties may not be achieved.

State of Trays and Packings

Remember that the actual number of trays required for a particular separation duty is determined by the efficiency of the plate, and the packings if packings are used. Thus, any factors that cause a decrease in tray efficiency will also change the performance of the column. Tray efficiencies are affected by fouling, wear and tear and corrosion, and the rates at which these occur depends on the properties of the liquids being processed. Thus appropriate materials should be specified for tray construction.

Weather Conditions

Most distillation columns are open to the atmosphere. Although many of the columns are insulated, changing weather conditions can still affect column operation. Thus the reboiler must be appropriately sized to ensure that enough vapour can be generated during cold and windy spells and that it can be turned down sufficiently during hot seasons. The same applies to condensors.

These are some of the more important factors that can cause poor distillation column performance. Other factors include changing operating conditions and throughputs, brought about by changes in upstream conditions and changes in the demand for the products. All these factors, including the associated control system, should be considered at the design stages because once a column is built and installed, nothing much can be done to rectify the situation without incurring significant costs. The control of distillation columns is a field in its own right, but that's another story.



0 0


  • kathrin
    What affects the performance of a distillation column?
    3 years ago
  • stig
    What affects column separation?
    2 years ago
  • aurelio
    What is the factor affecting on distillstion colmn?
    1 year ago
  • arsi madetoja
    How does weather affect reboiler?
    11 months ago
  • Haris
    What affects differential pressure in beer column distillation?
    10 months ago
  • pearl
    How reflux ratio affect column?
    10 months ago
  • ren
    How reflux rate affects compostition of distillation?
    9 months ago
  • Myrtle Whitfoot
    What affects flow rates in distillation column?
    9 months ago
  • Gigliola
    How odes reflux affect tower separation physically?
    7 months ago
  • falco took
    How feed affects delta pressure in distillation column?
    7 months ago
  • guido
    How does pressure drop affect a distillation column?
    6 months ago
  • martin docherty
    How might increasing the diameter of a column affect separation?
    6 months ago
  • rudigar
    What factors affect effective distillation and purity?
    3 months ago
  • andra
    What factors affect effective fractional distillation?
    3 months ago
  • uwe
    What are feed conditions for separation columns?
    3 months ago
  • Pierina
    How does distillation column length affect distillate?
    1 month ago

Post a comment